How to reach the TDM and install the VATS Passkey Bypass
The TDM is usually on the right side of the dash, but depending on the vehicle, it may also be behind the center console attached to the heater duct. If this is the case it is very difficult to get at as it is deep inside the dash and it's unlikely that you will be able to get it out, but you can likely feel the wires up in there.
Camaro TDM Connector
If the enclosure of your NEWROCKIES PRO Module is green and blue, please setup the switches as following (if enclosure is black, please submit a request to our support team for correct switch configurations):
Open the NEWROCKIES PRO Module's cover (this will NOT void the warranty) by removing the 2 screws on the bottom. Inside there are 2 sets of switches.
Set SW1 (8 switches) as following:
| DIP SWITCHES (SW1) | |||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| off | off | on | off | on | off | off | on |
Leave SW2 (10 switches) the way it is. Close the PRO Module's cover.
To install the NEWROCKIES PRO Module, connect it as following (the TDM should be left unplugged as it is not needed anymore):
|
PRO Bypass |
Car Wires |
|
RED |
Attach to the PINK with a BLACK stripe at the TDM Connector Pin A1 |
|
BLK |
Attach to the BLACKwith a WHITE stripe at the TDM connector Pin B1 |
|
PPL |
Attach to the DARK GREEN or Black with Yellow stripe wire at the TDM connector Pin A3 |
|
GRN |
Attach to the DARK BLUE wire at the TDM connector Pin A2 |
|
YEL |
Not used. |
|
WHT |
Not Used |
|
BRN |
Not used |
IMPORTANT: If your car still does not start, please follow the troubleshooting directions for Passkey 1/2/3 before contacting our support team. This will make it easier and faster for us to handle your support questions and will enable us to serve you better.
The installation is completed.
Option 2: Install the VATS Passkey Bypass directly at ECM
Alternative ECM direct wiring:
If the enclosure of your NEWROCKIES PRO Module is green and blue, please setup the switches as following (if enclosure is black, please submit a request to our support team for correct switch configurations):
Open the NEWROCKIES PRO Module's cover (this will NOT void the warranty) by removing the 2 screws on the bottom. Inside there are 2 sets of switches.
Set SW1 (8 switches) as following:
| DIP SWITCHES (SW1) | |||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| off | off | on | off | on | off | off | on |
Leave SW2 (10 switches) the way it is. Close the PRO Module's cover.
To install the NEWROCKIES PRO Module, connect it as following:
- GRN : Attach this wire from the Pro Module to the ECM connector C1, Pin B6 dark blue. It is between a purple white wire and a black wire.
- RED : Attach this wire from the Pro Module to the ECM connector C1, Pin A6, Pink. It is between brown white and tan black.
- BLK : Attach this wire from the Pro Module to the ECM connector C1, A11 or A12, black, system ground.
- At the Theft relay, which is located behind the left (drivers) kick panel, you need to cut the yellow and the dark green/white wires and splice them to eliminate that relay to enable the starter.
IMPORTANT: If your car still does not start, please follow the troubleshooting directions for PASSKEY 1/2/3 Systems before contacting our support team. This will make it easier and faster for us to handle your support questions and will enable us to serve you better.
The installation is completed.
0 Comments